Production introduction
Constructed with durability in mind, the monitor body of the Water Cannon For Mining is made from an aluminium alloy with a red epoxy powder coating. This coating not only enhances its visual appeal but also provides exceptional protection against the corrosive elements often present in mining areas, such as dust, chemicals, and moisture. The monitor nozzle, crafted from hard - anodized aluminium alloy, is designed to handle high - pressure water flow while maintaining precise water distribution. The handle, made of SS304 stainless steel, offers a firm grip and resists wear, enabling miners to operate the cannon effectively.
A key feature of the foinbo® Water Cannon For Mining is its ability to produce both straight steam and fog patterns. In mining, the straight - steam pattern is crucial for reaching fires in hard - to - access areas, such as deep mine shafts or narrow tunnels, and penetrating through thick smoke and flames. The fog pattern, on the other hand, is effective for cooling large areas, suppressing dust, and smothering fires in open - pit mines or storage areas for flammable materials.
The WM_A SERIES offers models like WM 8/20W - A, WM 8/30W - A, WM 8/40W - A, and WM 8/50W - A. The WM 8/20W - A has a flow rate of 1200 L/Min, operating at 8 bar with a maximum reach of 50 meters and a maximum fog angle of 120°. The WM 8/30W - A provides a flow rate of 1800 L/Min, also at 8 bar, with a maximum reach of 55 meters and a 120° fog angle. The WM 8/40W - A offers a flow rate of 2400 L/Min, operating at 8 bar, with a maximum reach of 60 meters and a 120° fog angle. The WM 8/50W - A has a flow rate of 3000 L/Min, at 8 bar, with a maximum reach of 65 meters and a 120° fog angle. All models are equipped with a 4 - inch/DN100 inlet flange compliant with BS4504, allowing for easy connection to the water supply systems in mines.
Products parameters
|
Model Number |
Flow Rate |
W.Pressure |
Max. Reach |
Max. Fog Angle |
Inlet Flange |
|
WM 8/20W–A |
1200 L/Min |
8 bar |
50 meters |
120° |
4 inch/DN100 @ BS4504 |
|
WM 8/30W–A |
1800 L/Min |
8 bar |
55 meters |
120° |
4 inch/DN100 @ BS4504 |
|
WM 8/40W–A |
2400 L/Min |
8 bar |
60 meters |
120° |
4 inch/DN100 @ BS4504 |
|
WM 8/50W–A |
3000 L/Min |
8 bar |
65 meters |
120° |
4 inch/DN100 @ BS4504 |
FAQ
Q: How does the Water Cannon For Mining handle the dusty environment in mines?
A: The Water Cannon For Mining is well - equipped to deal with dusty environments. The fog pattern can be used to suppress dust by creating a fine mist that weighs down the dust particles, preventing them from becoming airborne. Additionally, the robust construction of the monitor body, with its red epoxy powder coating, helps protect the cannon from dust ingress, reducing the risk of damage to its internal components. Regular cleaning and maintenance, including checking for dust accumulation in the nozzle and other parts, are also important to ensure its continued effective operation in dusty conditions.
Q: Can the Water Cannon For Mining be used in fires involving combustible mining materials?
A: Yes, the Water Cannon For Mining is effective in combating fires involving combustible mining materials. The straight - steam pattern can be used to directly target the fire source, reaching deep into piles of combustible materials or through narrow spaces. The fog pattern, on the other hand, can smother the fire by cooling the materials and cutting off the oxygen supply. However, it's important to ensure that the type of water used is appropriate for the specific combustible materials involved, and that safety protocols are strictly followed to prevent any secondary hazards.
Q: How often should I inspect and maintain the Water Cannon For Mining?
A: Given the harsh mining environment, regular inspection and maintenance of the Water Cannon For Mining are crucial. After each use, thoroughly clean the cannon to remove any dust, debris, or chemical residues. Inspect the red epoxy powder coating for any signs of damage, such as chips or cracks, and repair them promptly. Check the nozzle for blockages or wear, and lubricate the moving parts, including the handle and any control mechanisms, as per the manufacturer's recommendations. Conduct a more in - depth inspection at least once a month, checking the integrity of all components and ensuring that the cannon is in optimal working condition.
Q: What factors should I consider when choosing a model of the Water Cannon For Mining?
A: When choosing a model, consider the size and layout of the mining area. For larger mines or areas with complex layouts, a model with a higher flow rate and longer reach, such as WM 8/50W - A, would be more suitable to ensure comprehensive fire coverage. Also, take into account the specific fire risks in your mine, such as the presence of highly combustible materials or areas with difficult access. Additionally, consider the available water supply capacity and pressure in the mine to ensure compatibility with the chosen model.
Q: Can the Water Cannon For Mining be easily installed in different mining setups?
A: The Water Cannon For Mining is designed to be adaptable for installation in different mining setups. Its 4 - inch/DN100 inlet flange, compliant with BS4504, allows for standard connection to water supply systems in mines. However, the installation process may need to be customized depending on the specific layout and infrastructure of the mine. It's advisable to consult with a professional installer or the manufacturer to ensure proper installation, taking into account factors such as water pipe routing, support structures, and safety requirements in the mining environment.